Jump to content

Is this a good deal? Are these northwestern or a&a?


mppuzzled

Recommended Posts

2 of the big rack setups and the sticker machine for $800. Good deal? Just need to change coin mech and order new locks and keys. But don't need to drill them out cause they are already out. not sure what brand they are either. Thanks guys!

Sent from my SM-N915V using Tapatalk

2 of the big rack setups and the sticker machine for $800. Good deal? Just need to change coin mech and order new locks and keys. But don't need to drill them out cause they are already out. not sure what brand they are either. Thanks guys!

Sent from my SM-N915V using Tapatalk

8f8ce0ac130c3c18cff47b683d62934c.jpgdfc0688b1e11b5b42a9e36d462d93c14.jpg

Sent from my SM-N915V using Tapatalk

Link to comment
Share on other sites

It's not outrageous what they're asking, but I'd definitely go in lower since you'll need locks and coin mechs and you'd need to clean them up. I might start at $600 and see what he says. You can always go up from there.

Sent from my SM-N920V using Tapatalk

Link to comment
Share on other sites

Wow, 1300 is way too much. I don't know that he'd go any lower if you've already talked him down that much. Depends on how much you want it I suppose. I know I'd end up breaking the racks down into smaller ones. A 9-way with 2 wings would be kinda hard to locate, not impossible though.

Link to comment
Share on other sites

Why do you need coin mechs? Can't tell very good from the pic but it looks like the top machines may have NW mechs. If so they can be converted

These are way to big for 99% of most locations. You would be better off splitting the equipment up into smaller racks.

Link to comment
Share on other sites

Just need to take screws out of the bottom of the machines that holds them to the rack and theyll come right off. You can get shorter shelves and 2 more end pieces and you'll have 2 racks

Sent from my SM-N920V using Tapatalk

Link to comment
Share on other sites

I meant converting the coin mechs. Making them from .50 to .75. And the .25 to .50.

Sent from my SM-N915V using Tapatalk

 

You don't "Convert" mechs, you swap them out. The mechanisms have a little screw in the back that you can loosen, and they slide right out so you can drop a different coin mechanism in.

 

I suppose it is "possible" to convert a NW80/AA-2001 mech from 50 cents to 75, but that entails buying a new piece, taking the whole mech apart, then putting it all back together, and that's just a lot of work when you can buy a complete used mech for roughly the same price as a different coin carrier.

Link to comment
Share on other sites

I'd pass, A & A PN95s aren't near as good as Northwestern super 60s. The racks are too large for anything you're likely to get it. The mechs are not the correct denomination. It's just a big mess. I know it's hard but wait for a better opportunity.

Link to comment
Share on other sites

You don't "Convert" mechs, you swap them out. The mechanisms have a little screw in the back that you can loosen, and they slide right out so you can drop a different coin mechanism in.

I suppose it is "possible" to convert a NW80/AA-2001 mech from 50 cents to 75, but that entails buying a new piece, taking the whole mech apart, then putting it all back together, and that's just a lot of work when you can buy a complete used mech for roughly the same price as a different coin carrier.

I have converted many! Much cheaper than buying a new mech. Takes about 5 minutes.

Link to comment
Share on other sites

Hillbilly. How do I convert them? Is there a video or link you could send my way? And where do I get the parts that are needed?

Sent from my SM-N915V using Tapatalk

Link to comment
Share on other sites

Hillbilly. How do I convert them? Is there a video or link you could send my way? And where do I get the parts that are needed?

I dont know of any videos. A&A Global or NW. Do not interchange the parts.

Sent from my SM-N915V using Tapatalk

Link to comment
Share on other sites

Thanks for advice guys. I decided to pass on these. I should get better quality and smaller racks. looking for ones that dont need a lot of work done to them. Thanks.

Sent from my SM-N915V using Tapatalk

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...