nrod7
-
Posts
209 -
Joined
-
Last visited
Content Type
Profiles
Events
Forums
Downloads
Store
Gallery
Blogs
Articles
Classifieds
Everything posted by nrod7
-
Following up. The issue was a loose wire next to the compressor. Thanks AZVendor! nrod7
-
I have made sure that there is power from the wall outlet. The machine does not power up. Help! Thank you. nrod7
-
Thanks for all the advice. I will follow the feed back. You guys are the best! nrod7
-
Yes, refurbished. I pulled them from two working machines. I am thinking both coin mechs i tried are "bad.". Can i rule out that the bill validator is working correctly and that the coin mech needs to be replaced again? Thanks, nrod7
-
Mei 2511 is accepting dollar bills. Mars TRC- 6800H is not accepting coins ( drop straight thru) Have changed out coin mech twice with spare coin mechs. Problem not solved. Help! nrod7
-
Thanks for the feedback. The more I learn the more complicated the problems become. Your suggestions were confirmed by a local vending technician. In addition to checking for "pinches" in harness. It was suggested to spray, clean and air dry the harness connectors. Tomorrow I hope the machine will work correctly. Thanks, nrod7
-
Can You be a little more specific ? Harness from board, harness to vend motors? Thanks nrod7
-
Arrived at Location. The Machine was unplugged. The Chute had about 10 12 0z. can ( Jackpotted). "Out Of Service" On readout dispay. I cleared 3 Jammed columns. Closed Unit "Homing" displayed on read out display. None of the 6 motors stopped at the home position. Is this a "Board Problem." Help! nrod7
-
You guys are the best. I am sure to solve the issue with all the advice. I appreciate you'll taking the time to respond. Respectfully, nrod7
-
Thanks for the reply AngryChris, O,K, will do. Is the sold out switch attached to the "paddle sensor/housing" not sure what it is called? i did not change that switch. Also, It probably is not a "bad board" problem because the other columns are working properly, Correct? Thanks again. nrod7
-
Having a problem with column 3. All the other columns work fine. The LED readout reads "Sold out" 1. The column is full of product. 2. I check for a jammed can, no jam. 3. Motor cam was in the home position. 4. If, I hold the door sensor and motor switch the motor turns & a can drops. 5. Changed the motor switch and the selection switch. Still column 3 is reading "Sold out" Any suggestion? i thought about changing out the motor assembly, if that is not the answer, Let me know Why. Thanks, nrod7
-
Ok, thanks for the info. nrod7
-
This is a single price machine. How do I set machine to "Free Vend" I tried turning all the toggle switches to the "off" position in the coin validator settings. I tried pulling out the credit relay. Thanks, nrod7
-
Problem solved. Your suggestions helped me find that only column one was jackpotting. The motor switch (column one) was "bad" problem fixed. Thank you gentlemen for your support. Respectfully, nrod7
-
Vend price set at 1.00. When I insert a dollar bill it drops one 12 0z. can. The Problem is: if, I press the selection button again then, it drops two more cans ( without inserting any more money). What do I need to replace or check? Thanks, nrod7
-
Thanks for sharing your knowledge. I will probably go with a new relay and temperature sensor. I appreciate your time and patience. This forum has never let me down. Respectfully, nrod7
-
Thanks for clarifying that Mr. Lacanteen. That helps to learn exactly what that part does. Respectfully, nrod7
-
Converting electronic to manual thermostat. Which leads do I disconnect from electronic thermostat in order to connect new manual thermostat. Thanks, nrod7
-
I would like to convert the electronic thermostat to a manual thermostat. Please tell me which leads I need to disconnect from which relay , in order to connect to manual thermostat. ( By picture ) Is there another way to determine the right leads. Respectfully, nrod7 Could only put one picture on this post 2nd picture on following post RVCC- 804-9 (2)
-
As learned on this forum,( Thanks again) I am checking a cooling deck. I plugged the deck directly into a power source. The frostline begins to frost to were it needs to be, and the reefer feels cold to the touch. Should the frost line stay cold to the touch as long as the unit is plugged in, Or will it stop feeling cold because it is not in the machine? If the frost line stops feeing cold does the deck need servicing? Thanks, nrod7
-
Having trouble uploading images, any suggestions?
-
.thumb.jpg.bc740e77ab8d94aa9ec67a60f3e4dd22.jpg)
-
I called the Bottling Co. I was told the Asset & Serial number was no longer on the books. The unit was abandoned in a bankrupy business (Covid - 19), and was called to remove it. This is a very nice machine. What price is the range for sale? nrod7
-
All fixed now! it was a bad motor cluster switch on column 2. I want to thank you all for the help and advice. nrod7
-
Only column one is vending. Would one jammed motor keep the other columns from vending properly and would that keep the sold out light on continuously? Thanks, Nrod7
.jpg.b723a4e0f4ffa7638f3aa547d0aeb363.jpg)