Oasis Vending Posted April 28, 2017 Author Share Posted April 28, 2017 There isn't a B4 and C4! Explains that! My bill acceptor takes bills but doesn't register anything, coin mech works fine Link to comment Share on other sites More sharing options...
AZVendor Posted April 28, 2017 Share Posted April 28, 2017 Then those are phantom errors that could indicate further board problems are coming or that someone didn't properly reset the board when it was last repaired. Check the settings of switches 7 and 8 on the validator and try each combination. Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 4, 2017 Author Share Posted May 4, 2017 My M&M machine is accepting bills but won't register in display or give credit, second bill acceptor doing this Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 5, 2017 Author Share Posted May 5, 2017 I installed a BA30SA bill acceptor, I don't think it has switches to check Link to comment Share on other sites More sharing options...
AngryChris Posted May 5, 2017 Share Posted May 5, 2017 It does, the switches are inside the rectangular box Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 5, 2017 Author Share Posted May 5, 2017 I've tried 4 different bill acceptors, none of them show credit once it takes the bill. Could they all be bad? Help plz Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 5, 2017 Author Share Posted May 5, 2017 Takes coin and shows credit but not bills Link to comment Share on other sites More sharing options...
AngryChris Posted May 6, 2017 Share Posted May 6, 2017 At this point, I would question if you have a bad validator harness. Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 6, 2017 Author Share Posted May 6, 2017 Will send it in, thnx for input Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 6, 2017 Author Share Posted May 6, 2017 Oh harness, which one is that? White plug with 9 pins or the one that runs from board into bill acceptor? Link to comment Share on other sites More sharing options...
AngryChris Posted May 6, 2017 Share Posted May 6, 2017 Answer this first: what model validators did you try? Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 6, 2017 Author Share Posted May 6, 2017 Ba30sa coinco, it had a VN2511 originally, they all take the money and stack it in collector and gives no credit Link to comment Share on other sites More sharing options...
AngryChris Posted May 6, 2017 Share Posted May 6, 2017 Did you use a different harness for the coincos? Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 6, 2017 Author Share Posted May 6, 2017 No, same harness on all Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 6, 2017 Author Share Posted May 6, 2017 I don't have another harness I don't believe Link to comment Share on other sites More sharing options...
AngryChris Posted May 6, 2017 Share Posted May 6, 2017 The mars validator should require a different harness than the coincos. If you originally had a mars in there, then you should either get a new harness for the coincos or get a mars that works. Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 25, 2017 Author Share Posted May 25, 2017 After a three week wait for my bill acceptor to come back and a high bill, machine still takes money but doesn't register credit on display at all, same thing it has done with every bill acceptor I put in it. Takes coin and registers just fine, board? Link to comment Share on other sites More sharing options...
AZVendor Posted May 25, 2017 Share Posted May 25, 2017 Probably the board. Didn't you just replace it? If so then have them send you a warranty board. If this was a fleabay buy then you could be SOL. I have one that is rebuilt if you need it. Email me at rbepic4gatgmaildotcom. Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 25, 2017 Author Share Posted May 25, 2017 The board was rebuilt by vendnet or somebody, I bought a new harness last night, if that doesn't fix it, I will email you. Thanks Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 26, 2017 Author Share Posted May 26, 2017 AZVendor, did you get my email? Regarding board Link to comment Share on other sites More sharing options...
Oasis Vending Posted May 31, 2017 Author Share Posted May 31, 2017 Does anybody know of a tech support number I can call for this m&m machine? Link to comment Share on other sites More sharing options...
Oasis Vending Posted July 1, 2017 Author Share Posted July 1, 2017 The problem ended up being the wiring harness! Thanks for suggestions Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.