marzvending Posted March 25, 2013 Share Posted March 25, 2013 i have a vm010 bill changer that will take and accept bills but it wont give out change?? its not jammed the lights on the front are blinking green, ive noticed on the bill acceptor on the side there are numbers from 1-10 along with little switches , well 1-4 are off (switch pointing up) and 5-10 are on (switch point down). its filled with quarters...this is the machine can someone please help... Link to comment Share on other sites More sharing options...
bullyfrog Posted March 25, 2013 Share Posted March 25, 2013 I have no real experience with this brand or product but I do have contact info for them. You may be able to get them to send a manual or help walk you through some trouble shooting. http://www.pcm-tech.net/pg_contact.htm Sent from my EVO using Tapatalk 2 Link to comment Share on other sites More sharing options...
dogcow Posted March 25, 2013 Share Posted March 25, 2013 Inside the front left coin tube there's a small metal swirch near the bottom that indicates if the coin tubes are full. Make sure its being depressed properly and chk with a multimeter I've had those go bad Link to comment Share on other sites More sharing options...
dogcow Posted March 25, 2013 Share Posted March 25, 2013 Inside the front left coin tube there's a small metal swirch near the bottom that indicates if the coin tubes are full. Make sure its being depressed properly and chk with a multimeter I've had those go bad Link to comment Share on other sites More sharing options...
marzvending Posted March 25, 2013 Author Share Posted March 25, 2013 Inside the front left coin tube there's a small metal swirch near the bottom that indicates if the coin tubes are full. Make sure its being depressed properly and chk with a multimeter I've had those go bad Hey dogcow when the tubes are empty, on the front of the machine the lights blink yellow when i put in the quarters it blinks green.....should i mess with it still or is it doing what its suppose to??? Link to comment Share on other sites More sharing options...
dogcow Posted March 25, 2013 Share Posted March 25, 2013 Hey dogcow when the tubes are empty, on the front of the machine the lights blink yellow when i put in the quarters it blinks green.....should i mess with it still or is it doing what its suppose to??? If light works swirch is proh OK,what make/mdel is the val? Link to comment Share on other sites More sharing options...
marzvending Posted March 25, 2013 Author Share Posted March 25, 2013 If light works swirch is proh OK,what make/mdel is the val? im not understanding what VAL is??? Link to comment Share on other sites More sharing options...
dogcow Posted March 26, 2013 Share Posted March 26, 2013 Val=validator or bill acceptor Link to comment Share on other sites More sharing options...
Walta Posted March 26, 2013 Share Posted March 26, 2013 The BA looks like a JVL Walta Link to comment Share on other sites More sharing options...
AZVendor Posted March 31, 2013 Share Posted March 31, 2013 I have a "manual" for a CM-222 bill changer. This may not match your model number but these changers were sold by everyone selling the old mechanical machines. The bill head is very similar to yours. Here is what it says: The lights at the bill entrance should be on steady if the changer is ready to work. If the lights are flashing the changer is empty. Therefore: Problem: Indicator lights blink with coins in magazine. Check: Is the error light blinking on the side of the validator? Yes: Check validator for internal blockage. Check the Anticheat levers for proper operation. No: Is the magazine properly seated? No: Remove and reinsert magazine. Yes: Remove coin magazine and check pendulum. Does is swing freely on the brass bushing? Is the pendulum in the down position? Is the reflective surface on the pendulum clean? Check: Circuit board s/b on the back wall of changer. Remove connector from the circuit board at location J4. Short pins 1 & 2 with a metal object. Do the indicator lights continue to flash? Yes: Check for a broken wire (blue) from the dispenser sensor to circuit board J4. No: Replace dispenser sensor assembly. I hope this helps you out. Link to comment Share on other sites More sharing options...
bullyfrog Posted March 31, 2013 Share Posted March 31, 2013 The link I posted above is for the manufacturer. You should contact them directly. I keep manuals for all the machines I run. Sent from my EVO using Tapatalk 2 Link to comment Share on other sites More sharing options...
crushed59 Posted October 3, 2013 Share Posted October 3, 2013 hey all,new at this ,i have a vm-010 bill changer,has a prob,bills wont feed in machine,and the feed tray has 2 green lights that blink,it has change in the coin tubes,any advise on what the prob ight be,tks Link to comment Share on other sites More sharing options...
jcassad Posted January 12, 2015 Share Posted January 12, 2015 I also, am having issues with a VM-010 that prior has run error free for years. It started giving only 1-3 dollars in quarters for a 5 dollar bill, and eventually started shortchanging singles. Any ideas would be greatly appreciated. Link to comment Share on other sites More sharing options...
orsd Posted January 13, 2015 Share Posted January 13, 2015 Weak solenoid Junk it, sell the cabinet to people who use it as a bill box to retrofit older crane games with dba s Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.