putrevus Posted August 17, 2016 Share Posted August 17, 2016 Hi All, I am having issues with AP studio 3 , after entering the prices except three all of are showing 'd' and make another selection is flashing . I am at loss what am I doing wrong. Thanks again for you help Link to comment Share on other sites More sharing options...
lacanteen Posted August 17, 2016 Share Posted August 17, 2016 Have you tried to test vend? They may be off home. <service Mode> <button 5> <selection Number> Link to comment Share on other sites More sharing options...
putrevus Posted August 17, 2016 Author Share Posted August 17, 2016 Thanks a lot for your reply. Test vend is working fine. But actual vend when I put in money or card is showing error 'd' for all except one slot Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
lacanteen Posted August 17, 2016 Share Posted August 17, 2016 What's the history on this machine? Is this a machine you just purchased or is this a sudden problem with a working machine? Sounding like computer board. Link to comment Share on other sites More sharing options...
putrevus Posted August 17, 2016 Author Share Posted August 17, 2016 It's a refurbished machine I just purchased and just setting up for first time Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
lacanteen Posted August 17, 2016 Share Posted August 17, 2016 If the prices are set, it should give you the price if you press the selection number with no money. If you get the valid price, but still not getting with money, then you probably have a bad computer board. The Studio board is famous for motor driver issues. Link to comment Share on other sites More sharing options...
putrevus Posted August 17, 2016 Author Share Posted August 17, 2016 Thanks a lot I am going there again I will try again or get a new board. I have one question in vendo 721 in some columns with back spacer exactly the same and shim set is same but 6 columns are vending fine but 4 are giving issue two bottles are dropping at a time. When try cans by changing shim 3 are falling per vend. I have other vendo 721s I never had any issues in converting cans to bottles.can we vend monster in vendo 721. Thank you again for your help. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
AZVendor Posted August 18, 2016 Share Posted August 18, 2016 Are you adjusting the product clip in the rotor to match the length of your products? Link to comment Share on other sites More sharing options...
putrevus Posted August 18, 2016 Author Share Posted August 18, 2016 Are you adjusting the product clip in the rotor to match the length of your products? [/quoteThe product clip ? Can you plz tell me how do I do it. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
AZVendor Posted August 18, 2016 Share Posted August 18, 2016 It's on page G-11 of this part of the V21 manual: http://www.vendoco.com/Documents/1230247A%20General%20V21_10-2013_LR.pdf Here is the V21 programming if you need it as well: http://www.vendoco.com/Documents/1230298A_12.1%20Programming%20Trade_10-2013_LR.pdf Link to comment Share on other sites More sharing options...
putrevus Posted August 18, 2016 Author Share Posted August 18, 2016 It's on page G-11 of this part of the V21 manual: http://www.vendoco.com/Documents/1230247A%20General%20V21_10-2013_LR.pdf Here is the V21 programming if you need it as well: http://www.vendoco.com/Documents/1230298A_12.1%20Programming%20Trade_10-2013_LR.pdf I did exactly the same as shown in that page two columns 5 and 6 have the same side setup and product depth setup. Column 5 is vending fine but column 6 is vending two at time. None of columns I am able to vend cans as 3 cans are falling no matter where I put that side step. Thanks again for your help. That location is insisting on Monster cans can I vend them? Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
lacanteen Posted August 18, 2016 Share Posted August 18, 2016 I did exactly the same as shown in that page two columns 5 and 6 have the same side setup and product depth setup. Column 5 is vending fine but column 6 is vending two at time. None of columns I am able to vend cans as 3 cans are falling no matter where I put that side step. Thanks again for your help. That location is insisting on Monster cans can I vend them? Sent from my iPhone using Tapatalk Vend the Monster 2-deep. Set the slide retainer on the rotor to where the end is between the 2 cans. Make sure depth setting is 2. Make sure there is no extra product under the delivery chute as this will affect the drop sensor. Link to comment Share on other sites More sharing options...
putrevus Posted August 18, 2016 Author Share Posted August 18, 2016 Vend the Monster 2-deep. Set the slide retainer on the rotor to where the end is between the 2 cans. Make sure depth setting is 2. Make sure there is no extra product under the delivery chute as this will affect the drop sensor. Thank you for your help. What could be the reason why with 2 deep setting and the slider set exactly at same length two bottles are falling at time in one column and other is working fine. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
lacanteen Posted August 18, 2016 Share Posted August 18, 2016 Thank you for your help. What could be the reason why with 2 deep setting and the slider set exactly at same length two bottles are falling at time in one column and other is working fine. Sent from my iPhone using Tapatalk Might be motor speed or drop sensor. Link to comment Share on other sites More sharing options...
putrevus Posted August 18, 2016 Author Share Posted August 18, 2016 Might be motor speed or drop sensor. Thanks a lot for your help. it was drop sensor got it fixed. On Pepsi vendo model where priming is needed ,for 12 oz cans when vending first time after primed it is vending fine on next vend two are falling and then on third vend one is falling. This cycle is repeating. It was my bad on AP machine I did not set the prices properly. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.