Magiccity726 Posted November 23, 2022 Share Posted November 23, 2022 This machine has been working fine but now the display says sold out & it’s not sold out. It also is saying vend sensor. Then it says jammed. Column 1,2,3,4,5,6,7,8. How can I fix this issue? Thanks Link to comment Share on other sites More sharing options...
Zachsea Posted November 24, 2022 Share Posted November 24, 2022 Dont have any p series machines but have you checked the make sure the board plug ins are firm or not corroded? Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 25, 2022 Author Share Posted November 25, 2022 11 hours ago, Zachsea said: Dont have any p series machines but have you checked the make sure the board plug ins are firm or not corroded? All plugs on board are plugged in Link to comment Share on other sites More sharing options...
AZVendor Posted November 25, 2022 Share Posted November 25, 2022 Test vend all of your columns if it will let you. Otherwise, replacing the vend sensor will probably solve the issue. Those sensors are famous for being ruined by condensation that runs down into the sensor due to the poor design of it. I can list of a plethora of poor designs in this machine alone. Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 25, 2022 Author Share Posted November 25, 2022 25 minutes ago, AZVendor said: Test vend all of your columns if it will let you. Otherwise, replacing the vend sensor will probably solve the issue. Those sensors are famous for being ruined by condensation that runs down into the sensor due to the poor design of it. I can list of a plethora of poor designs in this machine alone. Ok thanks. Do you know where the sensor is located? Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 25, 2022 Author Share Posted November 25, 2022 Should I order the part from Dixie Narco? Link to comment Share on other sites More sharing options...
AZVendor Posted November 25, 2022 Share Posted November 25, 2022 (edited) It's located at the bottom of the delivery chute where it ends at the delivery door. You might find it at D&S or Vendors Exchange. Edited November 25, 2022 by AZVendor Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 25, 2022 Author Share Posted November 25, 2022 Thank you. Happy thanksgiving Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 28, 2022 Author Share Posted November 28, 2022 When I tried to change the vend sensor I noticed that one of the wires that connects to the vend sensor was not connected which I assume caused the problem. Not sure how to repair this wire though Link to comment Share on other sites More sharing options...
AZVendor Posted November 28, 2022 Share Posted November 28, 2022 Yup, that's the problem then. You might be able to replace the harness itself to get a new connector, otherwise you'll have to crack the connector open and re-solder the wire to the pin, if possible. Link to comment Share on other sites More sharing options...
Magiccity726 Posted November 29, 2022 Author Share Posted November 29, 2022 1 hour ago, AZVendor said: Yup, that's the problem then. You might be able to replace the harness itself to get a new connector, otherwise you'll have to crack the connector open and re-solder the wire to the pin, if possible. Do you know where the other end of that harness plugs into? Does it run all the way to the main board. Link to comment Share on other sites More sharing options...
AZVendor Posted November 29, 2022 Share Posted November 29, 2022 You'll have to check the manual or follow the harness yourself. I've never replaced one. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now